Toho-electronics TTM200 Manuel d'utilisateur Page 163
- Page / 264
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
48-7009-E 6-15
■ Control mode
SEt04
CNt
Setting content
Initial value
6
Md
RUN
Control start
RUN
MAN
Manual
RdY
Control stop
tIME1
Timer 1 operation
tIME2
Timer 2 operation
tIME3
Timer 3 operation
Set the control mode.
Control stop (RdY): Primary/secondary operating amount limiter lower limit is output.
Control start (RUN): Normal control is executed.
Manual (MAN): Operating amount set in the primary/secondary operating amount is output.
Timer interlocking control (tIME 1 to 3): A control where the normal control and timer operation are interlocked is executed.
For start (RUN)/stop (RdY)/manual (MAN) of control, see section “5.4.3 Mode/manual function” on page 5-28.
For timer interlocking control (tIME 1 to 3), see section “5.4.5 Timer function” on pages 5-32 to 37.
■ Control type setting
SEt04
CNt
Setting content
Initial value
7
CNt
0
Primary --- None
Secondary --- None
1
1
Primary --- PID control
Secondary --- None
2
Primary --- ONOFF control
Secondary --- None
3
Primary --- PID control
Secondary --- PID control
4
Primary --- PID control
Secondary --- ONOFF control
5
Primary --- ONOFF control
Secondary --- ONOFF control
6
Primary --- position proportional
Secondary --- position proportional
Set the control type (method).
Control types of primary and secondary control outputs that are set on this equipment can be assigned to the methods of 0 to 6.
For the content of the assignment, see the setting content listed above.
Note
(1) In case that the control type is set to 3 (primary/secondary PID control) and the tuning type to 3, 4 or 5, take care that the tuning
type changes to 1 (primary tuning) in conjunction with the change of the control type.
(2) Take care that the position proportional control (CNt: 6) is selectable even when the primary/secondary control output is not set
for the target connection setting.
■ PID control type/type B mode
SEt04
CNt
Setting content
Initial value
8
tYP
0
type A (normal PID control)
1
1
type B (overshoot suppression function)
2
type C (disturbance suppression function)
9
bMd
0
Overshoot suppression --- moderate
1
1
Overshoot suppression --- intermediate
2
Overshoot suppression --- intense
Set the PID control type.
For the use of the equipment in setting of the control type to be the PID control, a selection can be made among three control types of
0 (type A) to 2 (type C), whichever is best suited for the application.
Note The type B mode can be set when the PID control type is set to 1 (type B). In the type B mode, a result from integration (I) or
differentiation (d) of the auto-tuning is multiplied by a coefficient. The intermediate type is same value as it is. The type C
(disturbance suppression function) cannot be set when the self-tuning is set in the tuning type setting.
For control characteristics of each control type, see section “5.4.1 Auto-tuning (AT) function” on pages 5-23 to 25.
- User’s Manual 1
- ★ Precautions on safety 2
- ★ Alarm symbols 2
- ★ Other symbols 2
- Warnings 3
- Cautions 3
- ★ Summary notation 4
- ★ Notation of characters 4
- Contents 5
- 6. Parameters 6
- 7. Appendix 6
- 1. Overview 7
- 1.1 Feature 8
- TTM20 9
- ■ Front panel 10
- ■ Key operations 12
- ■ Others 12
- ■ Input section 14
- ■ Output section 15
- ■ Communication function 16
- 1.6 Basic flow of setting 17
- 2. Installation 18
- Panel cutting dimensions 21
- (9 6× n - 3 ) 22
- 3. Wiring 23
- 3.1 Precautions on wiring 24
- 3.2 Terminal arrangement 25
- DI 1 input 28
- DI 2 input 28
- DI 3 input 28
- DI 4 input 28
- 3.3 Wiring to each terminal 29
- TTM-205/209 30
- TTM-207 30
- 48-7009-E 3-13 35
- 3-4 Examples of wiring 37
- ★ Configuration example 38
- ★ Connection configuration 38
- 4. Basic operation 42
- 4.1 Flow of setting mode 43
- ■ Initial screen 44
- 4.2 Basic operation 45
- 48-7009-E 4-5 46
- 48-7009-E 4-6 47
- 48-7009-E 4-7 48
- 48-7009-E 4-8 49
- 48-7009-E 4-9 50
- 48-7009-E 4-10 51
- 48-7009-E 4-11 52
- 48-7009-E 4-12 53
- 48-7009-E 4-13 54
- 48-7009-E 4-14 55
- 48-7009-E 4-15 56
- 48-7009-E 4-16 57
- 48-7009-E 4-17 58
- 48-7009-E 4-18 59
- 48-7009-E 4-19 60
- 48-7009-E 4-21 62
- 48-7009-E 4-22 63
- 4.2.7 How to set outputs 66
- 48-7009-E 4-26 67
- 48-7009-E 4-27 68
- 5. Operating the equipment 71
- 5.3 How to set run settings 74
- 48-7009-E 5-5 75
- 48-7009-E 5-6 76
- 5.3.3 PID control setting 79
- 48-7009-E 5-10 80
- 48-7009-E 5-12 82
- 48-7009-E 5-14 84
- 5.3.5 Indicator setting 85
- 48-7009-E 5-16 86
- 48-7009-E 5-17 87
- 5.3.7 Event setting 88
- 48-7009-E 5-19 89
- 5.3.8 How to set MD/READY 90
- 48-7009-E 5-21 91
- 5.4.2 Self-tuning function 95
- 5.4.3 Mode/manual function 97
- 5.4.4 Bank function 98
- 5.4.5 Timer function 101
- AC line 110
- To equipment 110
- CT input 110
- Load: heater and such 110
- [When normal] 112
- Temperature 115
- MAX. 16 PARAMETER 117
- 16ﾊﾟﾗﾒｰﾀ 117
- SET21 PGF 122
- 48-7009-E 5-55 125
- 48-7009-E 5-60 130
- Wait range 131
- Example for StEPN 3 134
- SV value 135
- 48-7009-E 5-69 139
- Zone threshold setting 140
- Magnified 142
- SET23 ZBNK 143
- Max. 16 parameters 146
- 6. Explanation on parameters 149
- 6.1 Input 1 type setting 150
- 48-7009-E 6-12 160
- 48-7009-E 6-15 163
- 48-7009-E 6-18 166
- Proportional 167
- Deviation 168
- Setting value 168
- Proportional cycle 169
- 48-7009-E 6-31 179
- <Forward operation> 179
- 3 203
- Abnormality 206
- 6.7 DI setting 207
- 6.8 Timer function setting 210
- 6.10 Initial setting 215
- Ｔ Ｔ Ｍ－２ ０ ４ 220
- 48-7009-E 6-74 222
- 0～999（0．0～999．9）（℃） 222
- 48-7009-E 6-75 223
- ■Time Setting 223
- 6.14 PROGRAM SETTING 225
- 48-7009-E 6-78 226
- Threshold 228
- 7. Appendix 232
- 7.1 Product specifications 233
- 48-7009-E 7-3 234
- 48-7009-E 7-4 235
- 48-7009-E 7-5 236
- 48-7009-E 7-6 237
- 48-7009-E 7-7 238
- TTM-204 238
- TTM-205, 207 and 209 238
- 48-7009-E 7-8 239
- 7.2 Accessories 240
- 7.4 Troubleshooting 242
- 48-7009-E 7-12 243
- 7.5 Setting list 244
- 48-7009-E 7-14 245
- 48-7009-E 7-15 246
- 48-7009-E 7-16 247
- 48-7009-E 7-17 248
- 48-7009-E 7-18 249
- 48-7009-E 7-19 250
- 48-7009-E 7-20 251
- 48-7009-E 7-21 252
- 48-7009-E 7-22 253
- 48-7009-E 7-23 254
- 48-7009-E 7-24 255
- 48-7009-E 7-25 256
- 48-7009-E 7-26 257
- 48-7009-E 7-27 258
- 48-7009-E 7-28 259
- 48-7009-E 7-29 260
- 48-7009-E 7-30 261
- 48-7009-E 7-31 262
- 48-7009-E 7-32 263
- 48-7009-E 7-33 264
© 2020, manymanuals.fr. Tous droits réservés | 0.646 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels